Search Sort Posts:  Oldest to newest Newest to oldest

27/11/2007, 11:37 ErnieY Joined on 05/12/2006 Nr Prayssac (Lot) Posts 4,043 Re: Boiler heating hot water or not? My boiler is just plugged into an ordinary 2 pin socket and I think for less than €10 I bought a mechanical timer to control it with so why not simply add a socket to your existing arrangment and do likewise. The downside of such a simple arrangement is that in the event of a power cut the timer will stop until power is restored and therefore go out of sync with real time. The way around that would be to buy a more comprehensive one with a backup battery. Your boiler should have a label on it somewhere stating it's rating but at worst it's unlikely to exceed a few hundred watts. My doctor said one drink per day, I can live with that !    Report

27/11/2007, 23:37 robbie Joined on 18/06/2006 Posts 60 Re: Boiler heating hot water or not? after much diggin around, I am going to install a timer/programmer (battery backed) and alongside this a frost stat/pipe stat configuration. This should give me the flexibility for a series of eventualities. All I need now is enough oil in the flaming tank!!! Thanks guys for your responses and suggestions. I am off to France in dec and will hopefully resolve this issue then. I just hope the frost hasnt done anything in the meanwhile :)    Report

08/01/2008, 11:45 Yachty Joined on 08/01/2008 pres de Carcassonne Posts 22 Re: RE: Oil Heating, Hot water production and plumbing “funnies” in France Hello Peter, Just perusing the forums and came across your historic comments regarding woodfired CH systems. I have inherited a rather valueless but charming village house nr Carcassonne and intend to renovate it , as cost effectively as poss! Am considering installing some form of heating and hitherto had intended to use electric under floor mats to ground floor and a wood burner to our upper floor sitting room.  However, to increase the efficiency, it makes sense to consider installation of back boiler to service rads to other areas.  Frankly the house will not see much winter use but heating would be desired at some point. Cost of installation is the main consideration. If you feel inclined to advise, I would welcome some dialogue. Regards,   sebastian          Report

08/02/2008, 9:49 DavidF Joined on 07/02/2008 Posts 3 Re: RE: Oil Heating, Hot water production and plumbing “funnies” in France Thank you Opel Fruit  your post gives me an Idea on how to proceed with my project also have you ever used a pressure reduction unit on your mains water supply    Report

17/06/2008, 0:45 Lee&Nik Joined on 14/11/2007 nr Nontron Posts 41 Electric boiler instalation im sorry as im sure this may have been coverd before but i cant find it. i have a 200Li elec water boiler that i want to install, easy in UK 35amp hook up and hot cold in and out,  In France am i right in saying i need to fit a restrictor valve on the cold intake? and is it a 35amp hook up also which just attaches to the two screw connectors (live & neutral to either connector)?  and are there any other funnies?  earth? or is it as simple as i hope it will be? thankyou    Report

17/06/2008, 7:09 Nick Trollope Joined on 23/08/2004 Broons, Dept 22 Posts 2,490 Re: Electric boiler instalation Assuming that it is a French 200L chauffe-eau, then the supply is a 20A (dedicated) one. You need to fit a "groupe de securite" (safety valve) to the cold feed (which also provides a drain-off point) and a pressure reducer if the incoming pressure is above 3 bar (you should fit the PR to the incoming cold supply, otherwise the hot and cold water pressures will be unbalanced - contra to a very useful feature of pressurised hot water systems).   Nick www.aplaceinfrance.com    Report

17/06/2008, 18:51 powerdesal Joined on 07/01/2006 ex-Sharjah U.A.E Posts 2,203 Re: Electric boiler instalation Most definitely earth. There will be an earth terminal on the water heater which should be connected at the tableau to the earth bar. Dont install a water heater without an earth - please. Steve Back in the UAE (Fujeirah Emirate) + 50 (in France) ...........................................................................    Report

24/06/2008, 23:13 Lee&Nik Joined on 14/11/2007 nr Nontron Posts 41 Re: Electric boiler instalation Thanks for the advice, but can you tell me exactly what the  tableau to the earth bar is?  i was just going to earth it to the rest of the plumbing which itself is earthed, there are two terminal connectors that go through a small box then run onto the bottom of the tank, and also out of the small box is a metal strip which is bolted to the main tank which i presumed is where i take the earth from? i have a good clear picture but cant seem to paste it into this thread? thanks again peeps, lee    Report

04/07/2008, 2:22 Proxima Joined on 02/07/2008 Posts 21 A bit more on plumbing Great info. nicely laid out too. Can I just add a few things that may have been missed out. I did read through the thread but don't remember seeing this.. Plumbing; If you're using copper, then run all the main feed around to the areas you wish to supply in 18mm pipe. Once a point is reached, then you reduce down to the recomended sizes. These sizes are usually displayed in leaflets or display cards in places such as Mr. Bricolage etc. or can be found on the appliances themselves. If memory serves me well, it goes something like this, WC = 10mm Wash basin = 12mm Bath/kitchen sink = 14mm It's something like that, so keep your eyes open or enquire as to the correct way. Flexi connection hoses also come in these sizes, but are sometimes a bit of a pain to get a hold of.  I had a right laugh trying to make sure I got all the correct fittings in one run to the merchants rather than having to go back again for forgotten/never considered parts. Sometimes I found I would be visiting several different suppliers to get the exact bits required. One of the strangest things I ever saw was fully profesional French plumbers stood in the merchants for hours working out exactly which bits they wanted. I have seen this happen several times with different plumbers. Always stood around scratching there heads and checking over sketches or notes they made. If you've bought all your kitchen bathroom appliances, this will make life a bit easier. Either position the appliances or make a diagram of where you would like them to go...then measure up for all the pipe you'll need. Remember, 18mm for main runs, then 'Tee' off or feed to the appliances in required sizes. This way, you wont buy too much or too little of any particular pipe and you can work out from there exactly how many bends/straight couples/tee's/reducers you'll need. In the UK, the rule is 1 pipe clip every meter..so you can happily apply that principle in France too. I'm pretty sure there's no regs on pipe clips. A plumbing tip; If you've just done a connection to older plumbing and you can't get the old joint soldered, then replace the joint itself. Ensure the pipes on both sides (old/new) are cleaned with wire wool and wiped with a cloth. Sometimes this replacing of a joint will also solve the problem of getting a leak from a newly installed run of plumbing. You just somehow get that odd connection that never sits right. Again, replace the connection. The pipe doesn't matter too much as it's usually the connection that is the problem. Have you done your kitchen/bathroom in wood or other dark materials with low lighting? Are you showing the copper piping ? Buy a tube of autsol http://www.autosol.com/ and polish up all visible pipe/connections..you'll be amazed as to how it will look. It also helps to keep the pipe work in good condition and will never cease to amaze those who see it. Many will aks how you did it. Autosol meta polish (in the tubes) is a fine paste and rubs off the top surface of most metals. It will remove scratches and the more you use it the higher qulaity the finish. Copper and aluminium can be given a mirror finish.    Report

Page 13 of 14 (121 items) « First ... < 10 11 12 13 14 >

France Forum » Building and Re... » House Renovatio... » Re: RE: Oil Heating, Hot water production and plumbing “funnies” in France

(Quick links) Forums Home |- Search Forums |- Active Topics |- Unanswered Posts User Options |- Sign In |- Join this community |- Forgot Password About This Forum (READ ONLY) |- About This Forum Moving |- Finding/Owning French Property |- Making the Move From Outside the EU |- Long-Term Letting |- Employment Vacancies in France Legal and Finance |- French Legal Issues |- French Finance Building and Renovation |- House Renovations |-- Working with Wood Living |- Earning a Living |- Driving |- French Education |- Pets |- Animal Welfare, Rescue & Protection |- French Satellite TV, French Internet and Telephone |- Health |-- Changes to Healthcare Entitlement, CPAM, CMU and Cartes Vitales |- Swimming Pools in France Owning/Running a Business |- French Artisans |- Gite Owners |- Hotel and Restaurant Owners |- B&B/Chambres d'Hôtes Owners Leisure and Pastimes |- Gardening |- Sport, Leisure and Pastimes |- Shopping |- French Antiques, Arts & Crafts |- Photography |- Motorcycling in France |- Books and Literature |- Getting Married in France |- Pregnancy and Birth French Culture |- French Food and Wine |- French Culture |- French Language |-- French Language FAQs and Useful Links |- Wildlife/Nature/Environment |- French History Travelling to/from France |- Travelling to/from France |- Latest Good Value Deals to/from France Holidays |- Holidays General Discussion |- The Complete France Post Bag |- The Lighter Side |- Other Topics |- Forum Technical Support |- Useful Links About France/French Living Regions |- HOTEL SEARCH |- Central |- North East |- North West |- Paris Ile de France |- South East |- South West |- East |- West |- Corsica and DOM-TOMs