House Renovations

Topic has 25 replies.

Print Search
Sort Posts:    
   06/05/2008, 11:50
thunderhorse is not online. Last active: 04/09/2008 17:48:20 thunderhorse



Not Ranked
Joined on 16/11/2005
Deux-Sèvres
Posts 289
Oiling beech worktops
Reply Quote
I've just fitted the kitchen out with (unoiled) beechwood tops, and bought 3V3 huile plan de travail (both Castorama). I suspect the oil is linseed, but it says nothing on the tin, and Castorama didn't know... The manufacturers of the worktops give one set of advice for oiling, and instructions on the tin are markedly different (thicker coats). C'est la vie. Friends have suggested making sure to use Danish oil, not linseed.

So, is Danish oil any better than linseed? I also want to get the tops smooth and shiny asap. Would there likely be problems lighly sanding and oiling every week, say, until such is obtained?

Thanks for advice. Beer [B]

Roads? Where we're going we don't need roads.
   Report 
   06/05/2008, 11:57
Dick Smith is not online. Last active: 27/09/2008 04:58:04 Dick Smith



Top 10 Posts
Joined on 23/08/2004
Surrey and Manche (Pays Mortainais)
Posts 8,817
Re: Oiling beech worktops
Reply Quote
Danish oil hardens, Linseed stays slightly sticky is the wisdom.  I've just made a beech dining table and kitchen cabinet and used Danish Oil as a finish. It can be hard work!

The rule as I remember is to oil once an hour for a day, once a day for a week, once a week for a month and once a month therafter. Buffing in between. For the first few coats I denibbed using 240 grit finishing paper.

Make the sanding very light, as oil does not refinish the surface. If possible I would try a cabinet scraper rather than sandpaper. Danish oil is not very shiny unless you wax over it.

You might try using sanding sealer/oil on an offcut to see how it goes.

After many hours of work on the table top a varnish finish looked like an awfully attractive alternative!

Regards

Dick Smith

Nowhere is there warmth to be found
Among those afraid of losing their ground
   Report 
   06/05/2008, 12:53
Lilly is not online. Last active: 08/10/2008 12:34:17 Lilly



Not Ranked
Joined on 23/08/2004
Dordogne
Posts 102
Re: Oiling beech worktops
Reply Quote

Danish oil is your best bet, but I admit I have foung it difficult to find here, I have found it in a small bottle (no good for a floor!), if anyone knows how to find this in greater quantities I would be very greatfull. Incidently when the Danish oil is very dry you can indeed buff to a  shine, recommend buffing mop in the drill or similar attachment. Also if you can track it down a Hard wax oil is very hard wearing.

cheers

Lilly


   Report 
   06/05/2008, 13:01
Cat is not online. Last active: 10/10/2008 13:32:20 Cat



Top 50 Posts
Joined on 21/01/2005
------- Forum Moderator ------- Lot
Posts 3,197
Re: Oiling beech worktops
Reply Quote
There have been quite a few discussions in the past about oiling worktops and tables that you might like to read through

Cathy



Sun, sun, sun, here it comes...
   Report 
   06/05/2008, 16:51
toni is not online. Last active: 07/10/2008 15:23:03 toni

Not Ranked
Joined on 28/01/2006
Posts 66
Re: Oiling beech worktops
Reply Quote

We have beech worktops both at home and in France In France we use the IKEA 'behandla' oil which absorbs very easily but seems quite light in texture and needs to be applied a bit more often than the one we use here which is called 'Osmo' which seems thicker and lasts longer between coats. It is a mixture between  oil and wax and is pretty good. I see on the back of the can that if you require ''a deeper satin finish the surface can be polished usung 'Osmo Liquid Wax Cleaner' also available as a spray''. Haven't tried this but it might be worth looking into. The can says they have a website www.osmo.de.


   Report 
   06/05/2008, 19:20
Scooby is not online. Last active: 05/08/2008 17:53:11 Scooby

Not Ranked
Joined on 25/09/2007
Peak District
Posts 272
Re: Oiling beech worktops
Reply Quote
We used Danish oil (lots of coats!) and are very happy with the result.  We tried linseed oil first and it was a waste of time.  We did have to buy it in the UK though as we couldn't find anywhere that stocked it in France.

   Report 
   06/05/2008, 21:33
thunderhorse is not online. Last active: 04/09/2008 17:48:20 thunderhorse



Not Ranked
Joined on 16/11/2005
Deux-Sèvres
Posts 289
Re: Oiling beech worktops
Reply Quote
Many thanks so far. I'll continue with the 3V3 (I bought two tins, whatever oil it is...) and see how it goes. Opinion seems fairly divided on the issue of linseed v. Danish.

Big Smile [:D]

Roads? Where we're going we don't need roads.
   Report 
   06/05/2008, 21:56
J.R's gone native is not online. Last active: 04/09/2008 19:17:35 J.R's gone native

Top 75 Posts
Joined on 16/07/2006
Picardie, Sussex
Posts 1,947
Re: Oiling beech worktops
Reply Quote

I used Danish oil to start with but could not be ar5ed with the regular re-application.

Now I have a nice patinated farmhouse (grime) look with the added benefit that the anti-bacterial properties of the timber actually get a chance to earn their keep.

Every dog has its day unless buried under several coats of DanishSmile [:)]


   Report 
   06/05/2008, 22:04
Christine Animal is not online. Last active: 30/06/2008 12:28:36 Christine Animal



Top 25 Posts
Joined on 14/05/2005
Deux-Sèvres
Posts 4,322
Re: Oiling beech worktops
Reply Quote

Is there a reason for having beech worktops rather than granite, marble, tiles, etc. ?  A lot of you seem to be doing it, is it a fashion or you just like the idea of wood?

Where we were before we had a wooden surround for a washbasin, but just because I fancied it like that.  It was varnished and was waterproof, but is it really practical for a worktop?

 


animalaidsaintaubin.monsite.orange.fr/
Don't accept your dog's admiration as conclusive evidence that you are wonderful

   Report 
  Page 1 of 3 (26 items) 1 2 3 >
France Forum » Building and Re... » House Renovatio... » Re: Oiling beech worktops

Powered by Community Server, by Telligent Systems

Please note that any unsolicited advertising will be removed